Daily Papers

Focusing on simulated dilute polymer solutions, this letter investigates the interactions between flow structures and organized polymer stress sheets for the steady arrowhead coherent structure in a two-dimensional periodic channel flow. Formulating the problem in a frame of reference moving with the arrowhead velocity, streamlines, which are also pathlines in this frame, enables the identification of two distinct topological regions linked to two stagnation points. The streamlines help connecting the spatial distribution of polymer stress within the sheets and the dynamics of polymers transported by the flow. Using stresslines, lines parallel to the eigenvectors of polymer stress, a novel formulation of the viscoelastic stress term in the momentum transport equation proposes a more intuitive interpretation of the relation between the curvature of the stresslines, and the variation of stress along these lines, with the local flow topology. An approximation of this formulation is shown to explain the pressure jump observed in the arrowhead structure as a function of the local curvature of the polymer stress sheet.

In this article, we consider a viscoelastic plate equation with a logarithmic nonlinearity in the presence of nonlinear frictional damping term. Using the the Faedo-Galerkin method we establish the global existence of the solution of the problem and we also prove few general decay rate results.

In this work, we investigate the transient rheological behavior of two soft glassy materials: a clay dispersion and a silica gel, emphasizing their unconventional shear stress build-up behavior under conditions of constant imposed strain. For both materials, the elastic modulus and static yield stress undergo time-dependent evolution or aging. In addition, following an intense period of pre-shearing (i.e. shear-melting or destructuration), the material relaxation time is observed to show a stronger than linear dependence on the sample age, suggestive of hyper-aging dynamics. We show that these features are consistent with non-monotonic steady-state shear stress/shear rate flow curves characterized by a local stress minimum. When a steady shear flow is suddenly ceased, and the total imposed sample strain is held constant, both materials show an initial relaxation of the shear stress followed by a period of shear stress buildup, resulting in a local minimum in the evolution of shear stress with time. For the clay dispersion, the intensity of these effects increases with higher pre-shear rates, whereas for the silica gel, the effects are largely independent of the pre-shear rate. We also propose a simple time-dependent linear Maxwell model, which qualitatively predicts the experimentally observed trends in which the shear stress build-up is directly related to a monotonic increase in the elastic modulus, giving keen insight into this peculiar phenomenon.

The nonlinear rheology of a soft glassy material is captured by its constitutive relation, shear stress vs shear rate, which is most generally obtained by sweeping up or down the shear rate over a finite temporal window. For a huge amount of complex fluids, the up and down sweeps do not superimpose and define a rheological hysteresis loop. By means of extensive rheometry coupled to time-resolved velocimetry, we unravel the local scenario involved in rheological hysteresis for various types of well-studied soft materials. We introduce two observables that quantify the hysteresis in macroscopic rheology and local velocimetry respectively, as a function of the sweep rate δt^{-1}. Strikingly, both observables present a robust maximum with δt, which defines a single material-dependent timescale that grows continuously from vanishingly small values in simple yield stress fluids to large values for strongly time-dependent materials. In line with recent theoretical arguments, these experimental results hint at a universal timescale-based framework for soft glassy materials, where inhomogeneous flows characterized by shear bands and/or pluglike flow play a central role.

A finite difference scheme is used to develop a numerical method to solve the flow of an unbounded viscoelastic fluid with zero to moderate inertia around a prolate spheroidal particle. The equations are written in prolate spheroidal coordinates, and the shape of the particle is exactly resolved as one of the coordinate surfaces representing the inner boundary of the computational domain. As the prolate spheroidal grid is naturally clustered near the particle surface, good resolution is obtained in the regions where the gradients of relevant flow variables are most significant. This coordinate system also allows large domain sizes with a reasonable number of mesh points to simulate unbounded fluid around a particle. Changing the aspect ratio of the inner computational boundary enables simulations of different particle shapes ranging from a sphere to a slender fiber. Numerical studies of the latter particle shape allow testing of slender body theories. The mass and momentum equations are solved with a Schur complement approach allowing us to solve the zero inertia case necessary to isolate the viscoelastic effects. The singularities associated with the coordinate system are overcome using L'Hopital's rule. A straightforward imposition of conditions representing a time-varying combination of linear flows on the outer boundary allows us to study various flows with the same computational domain geometry. {For the special but important case of zero fluid and particle inertia we obtain a novel formulation that satisfies the force- and torque-free constraint in an iteration-free manner.} The numerical method is demonstrated for various flows of Newtonian and viscoelastic fluids around spheres and spheroids (including those with large aspect ratio). Good agreement is demonstrated with existing theoretical and numerical results.

The industrial application motivating this work is the fatigue computation of aircraft engines' high-pressure turbine blades. The material model involves nonlinear elastoviscoplastic behavior laws, for which the parameters depend on the temperature. For this application, the temperature loading is not accurately known and can reach values relatively close to the creep temperature: important nonlinear effects occur and the solution strongly depends on the used thermal loading. We consider a nonlinear reduced order model able to compute, in the exploitation phase, the behavior of the blade for a new temperature field loading. The sensitivity of the solution to the temperature makes {the classical unenriched proper orthogonal decomposition method} fail. In this work, we propose a new error indicator, quantifying the error made by the reduced order model in computational complexity independent of the size of the high-fidelity reference model. In our framework, when the {error indicator} becomes larger than a given tolerance, the reduced order model is updated using one time step solution of the high-fidelity reference model. The approach is illustrated on a series of academic test cases and applied on a setting of industrial complexity involving 5 million degrees of freedom, where the whole procedure is computed in parallel with distributed memory.

The classical theory of the wind-driven surface layer of a rotating ocean closes the momentum balance with a local flux-gradient law, in which the turbulent stress at a given depth is proportional to the shear at that depth. It predicts a surface current deflected forty-five degrees from the wind, which exceeds most direct measurements. This study asks what follows when locality is relaxed. Beginning from the exact integral relation between turbulent stress and mean shear, and requiring the memory kernel to carry no preferred vertical scale, we obtain a power-law kernel and therefore a stress law of fractional order. The resulting equation cannot be posed on the velocity, because the fractional derivative of a bounded profile vanishes at the surface, so the wind stress cannot be applied, while the alternative definition of the derivative leaves the surface current unbounded. Posed on the stress instead, the problem is solvable in closed form in Mittag-Leffler functions at every order between zero and one. The surface deflection then depends on the closure order alone and is smaller than forty-five degrees throughout, whereas the depth-integrated transport stays exactly normal to the wind, because that constraint follows from the momentum balance and not from the closure. The far field decays as a power law rather than exponentially, and its amplitude vanishes in the local limit, so that limit is singular. Under a suddenly applied stress the surface transient decays algebraically. Three independent algorithms agree closely, and no observational or model data are used.

Using absorbance measurements through a Couette cell containing an emulsion of buoyant droplets, volume fraction profiles are measured at various shear rates. These viscous resuspension experiments allow a direct determination of the normal stress in the vorticity direction in connection with the suspension balance model that has been developed for suspensions of solid particles. The results unambigously show that the normal viscosity responsible for the shear-induced migration of the droplets is independant on the capillary number, implying that particle deformation does not play a great role. It is similar to that of rigid particles at volume fractions below 40\% but much smaller at higher ones.

We show that Hertzian particle contacts are the underlying cause of the as-yet-unexplained noninteger power laws in weakly nonlinear rheology. In the medium amplitude oscillatory shear (MAOS) region, the cubic scaling of the leading order nonlinear shear stress (σ_3 sim γ_0^{m_3}, m_3=3) is the standard expectation. Expanding on the work by Natalia et al. [J. Rheol. 64 625-635 (2020)], we report an extensive data set of noncubical, noninteger power law scalings m_3 for particle suspensions in two immiscible fluids with a capillary attractive interaction, known as capillary suspensions. Here, we show that distinct power law exponents are found for the storage and loss moduli and these noninteger scalings occur at every secondary fluid concentration for two different contact angles. These compelling results indicate that the noninteger scalings are related to the underlying microstructure of capillary suspensions. We show that the magnitude of the third harmonic elastic stress scaling m_3,elastic originates from Hertzian-like contacts in combination with the attractive capillary force. The related third harmonic viscous stress scaling m_3,viscous is, found to be associated with adhesive-controlled friction. These observations, conducted for a wide range of compositions, can help explain previous reports of noninteger scaling for materials involving particle contacts and offers a new opportunity using the variable power law exponent of MAOS rheology to reveal the physics of particle bonds and friction in the rheological response under low deformation instead of at very high shear rates.

Recent flow cessation experiments on soft materials have shown a counter-intuitive non-monotonic relaxation of the shear stress: following the switch-off of a steady imposed shear flow, the stress initially decays before later increasing again. By simulating the soft glassy rheology model in a form extended to allow steady state shear banding, we show that the presence of shear bands prior to flow cessation can give rise to this phenomenon. We give a mechanistic understanding of the basic physics involved, in terms of (i) the decay of the shear bands after flow cessation, and (ii) the evolution of frustrated local stresses, governed by different time scales for plastic relaxation in each band. In particular, an elastic recoil in the unsheared band gives rise to negative local frustrated stresses, the slow release of which can cause an increase in macroscopic stress. Given that shear banding and frustrated local stresses arise widely across disordered soft solids, we argue that non-monotonic stress relaxation after flow cessation may occur in many different materials.

Nonlinear elastic properties of polymers and polymeric composites are essential for accurate prediction of their response to dynamic loads, which is crucial in a wide range of applications. These properties can be affected by strain rate, temperature, and pressure. The temperature susceptibility of nonlinear elastic moduli of polymers remains poorly understood. We have recently observed a significant frequency dependence of the nonlinear elastic (Murnaghan) moduli of polystyrene. In this paper we expand this analysis by the temperature dependence. The measurement methodology was based on the acousto-elastic effect, and involved analysis of the dependencies of velocities of longitudinal and shear single-frequency ultrasonic waves in the sample on the applied static pressure. Measurements were performed at different temperatures in the range of 25-65 {\deg}C and at different frequencies in the range of 0.75-3 MHz. The temperature susceptibility of the nonlinear moduli l and m was found to be two orders of magnitude larger than that of linear moduli lambda and mu. At the same time, the observed variations of n modulus with temperature were low and within the measurement tolerance. The observed tendencies can be explained by different influence of pressure on relaxation processes in the material at different temperatures.

In this paper, we introduce tensor involved peridynamics, a unified framework for simulating both isotropic and anisotropic materials. While traditional peridynamics models effectively simulate isotropic materials, they face challenges with anisotropic materials and are prone to instability caused by zero energy modes. Our novel model extend the linear bond based peridynamics framework by incorporating the elastic tensor into the micrmodulus function, thereby ensuring stability for anisotropic materials without the need for additional corrections. For isotropic materials. the model mantains compatibility with conventional bond based peridynamics, assuming Possion's rations of 1/4 in 3D and 1/3 in 2D.Numerical experiments confirm the model's stability and accuracy across various scenarios. Additionally, we introduce a damage model for isotropic materials. validating its performance in predicting crack propagation paths in a 2D plate. The results show superior alignment with experimental date compared to traditional model.

We derive a thermodynamically-consistent model of fluid flow through a poroelastic medium. Starting from elastic and fluid free-energy densities, an energy-dissipation rate, and a kinematic constraint, the force-balance equations are derived using variational principles, with the pressure--density constitutive relation emerging as a direct consequence of the variational structure; the same kinematic constraint also supplies the total-flux transport structure. In the ideal-gas limit, the model linearization recovers the classical linear Biot equations. For power-law fluid energies, it yields isentropic pressure--density relations. A key advantage of the variational formulation is that extensions to richer physics, such as thermal effects, chemical reactions, or multi-component fluids, can be incorporated systematically by augmenting the energy and dissipation functionals without redesigning the force-balance or transport closure. We support the model with an energy-compatible two-field discretization and study consolidation under a surface load with three lateral-boundary treatments and three fluid-compressibility exponents.

We consider the dictionary-based ROM-net (Reduced Order Model) framework [T. Daniel, F. Casenave, N. Akkari, D. Ryckelynck, Model order reduction assisted by deep neural networks (ROM-net), Advanced modeling and Simulation in Engineering Sciences 7 (16), 2020] and summarize the underlying methodologies and their recent improvements. The main contribution of this work is the application of the complete workflow to a real-life industrial model of an elastoviscoplastic high-pressure turbine blade subjected to thermal, centrifugal and pressure loadings, for the quantification of the uncertainty on dual quantities (such as the accumulated plastic strain and the stress tensor), generated by the uncertainty on the temperature loading field. The dictionary-based ROM-net computes predictions of dual quantities of interest for 1008 Monte Carlo draws of the temperature loading field in 2 hours and 48 minutes, which corresponds to a speedup greater than 600 with respect to a reference parallel solver using domain decomposition, with a relative error in the order of 2%. Another contribution of this work consists in the derivation of a meta-model to reconstruct the dual quantities of interest over the complete mesh from their values on the reduced integration points.

In recent years, there has been rapid development in 3D generation models, opening up new possibilities for applications such as simulating the dynamic movements of 3D objects and customizing their behaviors. However, current 3D generative models tend to focus only on surface features such as color and shape, neglecting the inherent physical properties that govern the behavior of objects in the real world. To accurately simulate physics-aligned dynamics, it is essential to predict the physical properties of materials and incorporate them into the behavior prediction process. Nonetheless, predicting the diverse materials of real-world objects is still challenging due to the complex nature of their physical attributes. In this paper, we propose Physics3D, a novel method for learning various physical properties of 3D objects through a video diffusion model. Our approach involves designing a highly generalizable physical simulation system based on a viscoelastic material model, which enables us to simulate a wide range of materials with high-fidelity capabilities. Moreover, we distill the physical priors from a video diffusion model that contains more understanding of realistic object materials. Extensive experiments demonstrate the effectiveness of our method with both elastic and plastic materials. Physics3D shows great potential for bridging the gap between the physical world and virtual neural space, providing a better integration and application of realistic physical principles in virtual environments. Project page: https://liuff19.github.io/Physics3D.

In the last decade many research efforts have been focused on understanding the rheology of disordered materials, and several theoretical predictions have been put forward regarding their yielding behavior. Nevertheless, not many experiments nor molecular dynamics simulations were dedicated to testing those theoretical predictions. Here we use computer simulations to study the yielding transition under two different loading schemes: standard simple shear dynamics, and self-propelled, dense active systems. In the active systems a yielding transition is observed as expected, when the self-propulsion is increased. However, the range of self-propulsions in which a pure liquid regime exist appears to vanish upon approaching the so-called "jamming point" at which solidity of soft-sphere packings is lost. Such an "active yielding" transition shares similarities with the generic yielding transition for shear flows. A Herschel-Bulkley law is observed in both loading scenarios, with a clear difference in the critical scaling exponents between the two, suggesting the existent of different universality classes for the yielding transition under different driving conditions. In addition, we present direct measurements of length and time scales for both driving scenarios. A comparison with theoretical predictions from recent literature reveals poor agreement with our numerical results.

Large language model (LLM)-based agentic frameworks increasingly adopt the paradigm of dynamically generating task-specific agents. We suggest that not only agents but also specialized software modules for scientific and engineering tasks can be generated on demand. We demonstrate this concept in the field of solid mechanics. There, so-called constitutive models are required to describe the relationship between mechanical stress and body deformation. Constitutive models are essential for both the scientific understanding and industrial application of materials. However, even recent data-driven methods of constitutive modeling, such as constitutive artificial neural networks (CANNs), still require substantial expert knowledge and human labor. We present a framework in which an LLM generates a CANN on demand, tailored to a given material class and dataset provided by the user. The framework covers LLM-based architecture selection, integration of physical constraints, and complete code generation. Evaluation on three benchmark problems demonstrates that LLM-generated CANNs achieve accuracy comparable to or greater than manually engineered counterparts, while also exhibiting reliable generalization to unseen loading scenarios and extrapolation to large deformations. These findings indicate that LLM-based generation of physics-constrained neural networks can substantially reduce the expertise required for constitutive modeling and represent a step toward practical end-to-end automation.

Data-driven surrogate models improve the efficiency of simulating continuous dynamical systems, yet their autoregressive rollouts are often limited by instability and spectral blow-up. While global regularization techniques can enforce contractive dynamics, they uniformly damp high-frequency features, introducing a contraction-dissipation dilemma. Furthermore, long-horizon trajectory optimization methods that explicitly correct drift are bottlenecked by memory constraints. In this work, we propose Jacobian-Adaptive Weighting for Stability (JAWS), a probabilistic regularization strategy designed to mitigate these limitations. By framing operator learning as Maximum A Posteriori (MAP) estimation with spatially heteroscedastic uncertainty, JAWS dynamically modulates the regularization strength based on local physical complexity. This allows the model to enforce contraction in smooth regions to suppress noise, while relaxing constraints near singular features to preserve gradients, effectively realizing a behavior similar to numerical shock-capturing schemes. Experiments demonstrate that this spatially-adaptive prior serves as an effective spectral pre-conditioner, which reduces the base operator's burden of handling high-frequency instabilities. This reduction enables memory-efficient, short-horizon trajectory optimization to match or exceed the long-term accuracy of long-horizon baselines. Evaluated on the 1D viscous Burgers' equation, our hybrid approach improves long-term stability, shock fidelity, and out-of-distribution generalization while reducing training computational costs.

The residual stress induced in assembly is a common concern in electronic packaging. The mismatch in coefficient of thermal expansion between borosilicate glass and silicon, upon temperature variation, generates an internal stress state. This affects important characteristics of microelectromechanical devices or constituent elements. Such as self frequence or stiffness. Stresses caused by thermal expansion coefficients mismatch of anodically bonded glass and silicon samples are studied in this paper. Stress calculation based on lamination theory is presented. Usage examples of such calculations are described. For bonded silicon and LK-5 glass several results of calculations are presented. Stress distribution in bonded silicon and glass of several thicknesses is evaluated. Stress distribution in bonded glass-silicon-glass structure is evaluated. Bonded silicon surface stress dependence of glass to silicon wafer thickness ratio is evaluated. Experimental study of thermal mismatch stress in glass based on birefringence phenomenon was conducted. It's results are presented in this paper. Keywords: anodic bonding, field assisted bonding, thermal expansion, stress.

We propose a physics-informed machine learning framework called P-DivGNN to reconstruct local stress fields at the micro-scale, in the context of multi-scale simulation given a periodic micro-structure mesh and mean, macro-scale, stress values. This method is based in representing a periodic micro-structure as a graph, combined with a message passing graph neural network. We are able to retrieve local stress field distributions, providing average stress values produced by a mean field reduced order model (ROM) or Finite Element (FE) simulation at the macro-scale. The prediction of local stress fields are of utmost importance considering fracture analysis or the definition of local fatigue criteria. Our model incorporates physical constraints during training to constraint local stress field equilibrium state and employs a periodic graph representation to enforce periodic boundary conditions. The benefits of the proposed physics-informed GNN are evaluated considering linear and non linear hyperelastic responses applied to varying geometries. In the non-linear hyperelastic case, the proposed method achieves significant computational speed-ups compared to FE simulation, making it particularly attractive for large-scale applications.

In this paper, we revisit the joint low-Mach and low-Frode number limit for the compressible Navier-Stokes equations with degenerate, density-dependent viscosity. Employing the relative entropy framework based on the concept of κ-entropy, we rigorously justify the convergence of weak solutions toward the generalized anelastic system in a three-dimensional periodic domain for well-prepared initial data. For general ill-prepared initial data, we establish a similar convergence result in the whole space, relying essentially on dispersive estimates for acoustic waves. Compared with the work of Fanelli and Zatorska [Commun. Math. Phys., 400 (2023), pp. 1463-1506], our analysis is conducted for the standard isentropic pressure law, thereby eliminating the need for the cold pressure term that played a crucial role in the previous approach. To the best of our knowledge, this is the first rigorous singular limit result for the compressible Navier-Stokes equations with degenerate viscosity that requires no additional regularization of the system.

Hyperelastic models have been widely used to model polymers and soft tissues. However, most hyperelastic models are phenomenological material models. Based on statistical mechanics and molecular chain configuration, 8 chain model or Arruda-Boyce model is a physical model which can be used to understand how microstructures of chains affect macroscopic mechanical properties of polymers and soft tissues. Mechanical properties of many polymers and soft tissues are directional dependent. Polymer matrix can be reinforced by fibers. For soft tissues, ligaments and tendons will lead to anisotropic properties. Since matrix and reinforcements are composed of similar microstructural molecular chains, they can be modeled by using the same mathematical model. In this paper, a series of 8 chain models is used to understand composite properties. That is, an isotropic 8 chain model will be used to model matrix and anisotropic 8 chain models will be used to model fibers. Replacing I_1 in isotropic 8 chain model with I_4 in anisotropic 8 chain model is physically corresponding to changing representative 8 chain cubic cell to 8 chain slender cell. This treatment not only simplifies exist anisotropic mathematical structures but also keeps microscopic physics of 8 chain model unchanged.

This study explores cardiovascular stents fabricated using laser powder bed fusion (LPBF); an emerging method to offer patient-specific customisable parts. Here, the shape memory alloy NiTi, in a near equiatomic composition, was investigated to deconvolve the material response from macroscopic component effects. Specifically, stress-geometry interactions were revealed, in-situ, for a minaturised cardiovascular stent subjected to an externally applied cylindrical stress whilst acquiring synchrotron X-ray imaging and diffraction data. The approach enabled the collection of spatially resolved micromechanical deformation data; the formation of stress-induced martensite and R-phase was evident, occurring in locations near junctions between stent ligaments where stress concentrations exist. In the as-fabricated condition, hardness maps were obtained through nanoindentation, demonstrating that the localised deformation and deformation patterning is further controlled by porosity and microstructural heterogeneity. Electron backscatter diffraction (EBSD) supported these observations, showing a finer grain structure near stent junctions with higher associated lattice curvature. These features, combined with stress concentrations when loaded will initiate localised phase transformations. If the stent was subjected to repeated loading, representing in-vivo conditions, these regions would be susceptible to cyclic damage through transformation memory loss, leading to premature component failure. This study highlights the challenges that must be addressed for the post-processing treatment of LABF-processed stents for healthcare-related applications.

This work puts forth a new optimal design formulation for planar elastic membranes. The goal is to minimize the membrane's compliance through choosing the material distribution described by a positive Radon measure. The deformation of the membrane itself is governed by the convexified F\"{o}ppl's model. The uniqueness of this model lies in the convexity of its variational formulation despite the inherent nonlinearity of the strain-displacement relation. It makes it possible to rewrite the optimization problem as a pair of mutually dual convex variational problems. In the primal problem a linear functional is maximized with respect to displacement functions while enforcing that point-wisely the strain lies in an unbounded closed convex set. The dual problem consists in finding equilibrated stresses that are to minimize a convex integral functional of linear growth defined on the space of Radon measures. The pair of problems is analysed: existence and regularity results are provided, together with the system of optimality criteria. To demonstrate the computational potential of the pair, a finite element scheme is developed around it. Upon reformulation to a conic-quadratic & semi-definite programming problem, the method is employed to produce numerical simulations for several load case scenarios.

The transition of an impulsively excited kink oscillation of a solar coronal loop to an oscillation with a stationary amplitude, i.e., the damping pattern, is determined using the low-dimensional self-oscillation model. In the model, the decayless kink oscillations are sustained by the interaction of the oscillating loop with an external quasi-steady flow. The analytical solution is based on the assumption that the combined effect of the effective dissipation, for example, by resonant absorption, and interaction with an external flow, is weak. The effect is characterised by a dimensionless coupling parameter. The damping pattern is found to depend upon the initial amplitude and the coupling parameter. The approximate expression shows a good agreement with a numerical solution of the self-oscillation equation. The plausibility of the established damping pattern is demonstrated by an observational example. Notably, the damping pattern is not exponential, and the characteristic decay time is different from the time determined by the traditionally used exponential damping fit. Implications of this finding for seismology of the solar coronal plasmas are discussed. In particular, it is suggested that a very rapid, in less than the oscillation period, decay of the oscillation to the stationary level, achieved for larger values of the coupling parameter, can explain the relative rareness of the kink oscillation events.

In this paper, we propose a { P_{1}^{c}}RT0-P0 discretization of the Stokes equations on general simplicial meshes in two/three dimensions (2D/3D), which yields an exactly divergence-free and pressure-independent velocity approximation with optimal order. Our method has the following features. Firstly, the global number of the degrees of freedom of our method is the same as the low order Bernardi and Raugel (B-R) finite element method (Bernardi and Raugel, 1985), while the number of {the non-zero entries} of the former is about half of the latter in the velocity-velocity region of the coefficient matrix. Secondly, the { P_{1}^{c}} component of the velocity, the RT0 component of the velocity and the pressure seem to solve a popular { P_{1}^{c}}-{RT0}-P0 discretization of a poroelastic-type system formally. Finally, our method can be easily transformed into a pressure-robust and stabilized { P_{1}^{c}}-P0 discretization for the Stokes problem via the static condensation of the RT0 component, which has a much smaller number of global degrees of freedom. Numerical experiments illustrating the robustness of our method are also provided.

In this paper we consider a particular class of solutions of the Rayleigh-Boltzmann equation, known in the nonlinear setting as homoenergetic solutions, which have the form gleft( x,v,t right) =fleft( v-Lleft( tright)x,tright) where the matrix L(t) describes a shear flow deformation. We began this analysis in [22] where we rigorously proved the existence of a stationary non-equilibrium solution and established the different behaviour of the solutions for small and large values of the shear parameter, for cut-off collision kernels with homogeneity parameter 0leq gamma <1, including Maxwell molecules and hard potentials. In this paper, we concentrate in the case where the deformation term dominates the collision term for large times (hyperbolic-dominated regime). This occurs for collision kernels with gamma < 0 and in particular we focus on gamma in (-1,0). In such a hyperbolic-dominated regime, it appears challenging to provide a clear description of the long-term asymptotics of the solutions. Here we present a formal analysis of the long-time asymptotics for the distribution of velocities and provide the explicit form for the asymptotic profile. Additionally, we discuss the different asymptotic behaviour expected in the case of homogeneity gamma < -1. Furthermore, we provide a probabilistic interpretation describing a stochastic process consisting in a combination of collisions and shear flows. The tagged particle velocity {v(t)}_{tgeq 0} is a Markov process that arises from the combination of free flights in a shear flow along with random jumps caused by collisions.

We study the problem of the transformation of a given reactant species into an immiscible product species, as they flow through a chemically active porous medium. We derive the equation governing the evolution of the volume fraction of the species -- in a one-dimensional macroscopic description --, identify the relevant dimensionless numbers, and provide simple models for capillary pressure and relative permeabilities, which are quantities of crucial importance when tackling multiphase flows in porous media. We set the domain of validity of our models and discuss the importance of viscous coupling terms in the extended Darcy's law. We investigate numerically the steady regime and demonstrate that the spatial transformation rate of the species along the reactor is non-monotonous, as testified by the existence of an inflection point in the volume fraction profiles. We obtain the scaling of the location of this inflection point with the dimensionless lengths of the problem. Eventually, we provide key elements for optimization of the reactor.

Accurate grasp force control is one of the key skills for ensuring successful and damage-free robotic grasping of objects. Although existing methods have conducted in-depth research on slip detection and grasping force planning, they often overlook the issue of adaptive tracking of the actual force to the target force when handling objects with different material properties. The optimal parameters of a force tracking controller are significantly influenced by the object's stiffness, and many adaptive force tracking algorithms rely on stiffness estimation. However, real-world objects often exhibit viscous, plastic, or other more complex nonlinear time-varying behaviors, and existing studies provide insufficient support for these materials in terms of stiffness definition and estimation. To address this, this paper introduces the concept of generalized stiffness, extending the definition of stiffness to nonlinear time-varying grasp system models, and proposes an online generalized stiffness estimator based on Long Short-Term Memory (LSTM) networks. Based on generalized stiffness, this paper proposes an adaptive parameter adjustment strategy using a PI controller as an example, enabling dynamic force tracking for objects with varying characteristics. Experimental results demonstrate that the proposed method achieves high precision and short probing time, while showing better adaptability to non-ideal objects compared to existing methods. The method effectively solves the problem of grasp force tracking in unknown, nonlinear, and time-varying grasp systems, demonstrating the generalization capability of our neural network and enhancing the robotic grasping ability in unstructured environments.

The dynamical realisation of the equation of state p +rho =0 is studied. A non-pathological dynamics for the perturbations of such a system mimicking a dynamical cosmological constant (DCC) requires to go beyond the perfect fluid paradigm. It is shown that an anisotropic stress must be always present. The Hamiltonian of the system in isolation resembles the one of a Pais-Uhlenbeck oscillator and linear stability requires that it cannot be positive definite. The dynamics of linear cosmological perturbations in a DCC dominated Universe is studied in detail showing that when DCC is minimally coupled to gravity no dramatic instability is present. In contrast to what happens in a cosmological constant dominated Universe, the non-relativistic matter contrast is no longer constant and exhibits an oscillator behaviour at small scales while it grows weakly at large scales. In the gravitational waves sector, at small scales, the amplitude is still suppressed as the inverse power of the scale factor while it grows logarithmically at large scales. Also the vector modes propagate, though no growing mode is found.

Modelling physical systems with partial differential equations (PDEs) is central to science and engineering, yet in most real applications the PDE model is incomplete: relationships such as constitutive or thermal laws are unknown. Existing surrogate approaches close this gap by learning the PDE solution from data, but remain tied to a specific configuration (geometry, boundary conditions, discretisation) and recover the solution rather than the missing physics itself. We introduce FEML, an end-to-end differentiable framework that couples the known PDE with a machine-learned operator for the missing physics. Embedding the PDE solver into training lets this operator be learned directly from the PDE solution, even when its own output cannot be measured - for example, stress in constitutive laws. Because the operator is independent of the system configuration, a law learned in one setting transfers zero-shot to new geometries, boundary conditions, and discretisations, and can be inspected by domain specialists. FEML represents the operator with structure-preserving operator networks (SPONs), which retain key continuous properties at the discrete level. We demonstrate FEML across solid mechanics and thermal transport. From synthetic data we progressively discover an elastoplastic law - the nonlinear elastic response, then the plastic hardening law - and compose them into a foundation constitutive model that transfers zero-shot to a 3D torsion problem. Moving to real data, we learn coupled plastic-hardening and ductile-damage laws from a benchmark shear-coupon test, reproducing the measured response, including post-peak softening, to within the experimental scatter. Finally, we recover a temperature-dependent conductivity from transient heat-flow data and apply symbolic regression to the learned operator to extract a closed-form law matching the ground truth.

Proprioception is the "sixth sense" that detects limb postures with motor neurons. It requires a natural integration between the musculoskeletal systems and sensory receptors, which is challenging among modern robots that aim for lightweight, adaptive, and sensitive designs at a low cost. Here, we present the Soft Polyhedral Network with an embedded vision for physical interactions, capable of adaptive kinesthesia and viscoelastic proprioception by learning kinetic features. This design enables passive adaptations to omni-directional interactions, visually captured by a miniature high-speed motion tracking system embedded inside for proprioceptive learning. The results show that the soft network can infer real-time 6D forces and torques with accuracies of 0.25/0.24/0.35 N and 0.025/0.034/0.006 Nm in dynamic interactions. We also incorporate viscoelasticity in proprioception during static adaptation by adding a creep and relaxation modifier to refine the predicted results. The proposed soft network combines simplicity in design, omni-adaptation, and proprioceptive sensing with high accuracy, making it a versatile solution for robotics at a low cost with more than 1 million use cycles for tasks such as sensitive and competitive grasping, and touch-based geometry reconstruction. This study offers new insights into vision-based proprioception for soft robots in adaptive grasping, soft manipulation, and human-robot interaction.

Asphalt concrete's (AC) durability and maintenance demands are strongly influenced by its fatigue life. Traditional methods for determining this characteristic are both resource-intensive and time-consuming. This study employs artificial neural networks (ANNs) to predict AC fatigue life, focusing on the impact of strain level, binder content, and air-void content. Leveraging a substantial dataset, we tailored our models to effectively handle the wide range of fatigue life data, typically represented on a logarithmic scale. The mean square logarithmic error was utilized as the loss function to enhance prediction accuracy across all levels of fatigue life. Through comparative analysis of various hyperparameters, we developed a machine-learning model that captures the complex relationships within the data. Our findings demonstrate that higher binder content significantly enhances fatigue life, while the influence of air-void content is more variable, depending on binder levels. Most importantly, this study provides insights into the intricacies of using ANNs for modeling, showcasing their potential utility with larger datasets. The codes developed and the data used in this study are provided as open source on a GitHub repository, with a link included in the paper for full access.

Mechanically interlocked polymers (MIPs) are a novel class of polymer structures in which the components are connected by mechanical bonds instead of covalent bonds. We measure the single-molecule rheological properties of polyrotaxanes, daisy chains, and polycatenanes under steady shear and steady uniaxial extension using coarse-grained Brownian dynamics simulations with hydrodynamic interactions. We obtain key rheological features, including tumbling dynamics, molecular extension, stress, and viscosity. By systematically varying structural features, we demonstrate how MIP topology governs flow response. Compared to linear polymers, all three MIP architectures exhibit enhanced tumbling in shear flow and lower normal stress differences in extensional flow. While polyrotaxanes show higher shear and extensional viscosities, polycatenanes and daisy chains have lower viscosities. In extensional flow, polyrotaxanes and polycatenanes extend earlier than linear polymers. We find that mechanical bonds suppress shear thinning and alter the coil-stretch transition observed in linear polymers. These effects arise from the mechanically bonded rings in MIPs, which expand the polymer profile in gradient direction and increase backbone stiffness due to ring-backbone repulsions. This study provides key insights into MIP flow properties, providing the foundation for their systematic development in engineering applications.

We consider the matrix composite materials (CM) of either random (statistically homogeneous or inhomogeneous), periodic, or deterministic (neither random nor periodic) structures. CMs exhibit linear or nonlinear behavior, coupled or uncoupled multi-physical phenomena, locally elastic, weakly nonlocal (strain gradient and stress gradient), or strongly nonlocal (strain-type and displacement-type, peridynamics) phase properties. A modified Computational Analytical Micromechanics (CAM) approach introduces an exact Additive General Integral Equation (AGIE) for CMs of any structure and phase properties mentioned above. The unified iteration solution of static AGIEs is adapted to the body force with compact support serving as a fundamentally new universal training parameter. The approach also establishes a critical threshold for filtering out unsuitable sub-datasets of effective parameters through a novel Representative Volume Element (RVE) concept, which extends Hill's classical framework. This RVE concept eliminates sample size, boundary layer, and edge effects, making it applicable to CMs of any structure and phase properties, regardless of local or nonlocal, linear or nonlinear. Incorporating this new RVE concept into machine learning and neural network techniques enables the construction of any unpredefined surrogate nonlocal operators. The methodology is structured as a modular, block-based framework, allowing independent development and refinement of software components. This flexible, robust AGIE-CAM framework integrates data-driven, multi-scale, and multi-physics modeling, accelerating research in CM of any microtopology and phase properties considered. The AGIE-CAM framework represents a groundbreaking paradigm shift in the micromechanics of composites, redefining the very philosophy that underpins our understanding of their behavior at the microscopic level.

Introduction: Mechanical thrombectomy can cause vessel deformation and procedure-related injury. Benchtop models are widely used for device testing, but time-resolved, full-field 3D vessel-motion measurements remain limited. Methods: We developed a nine-camera, low-cost multi-view workflow for benchtop thrombectomy in silicone middle cerebral artery phantoms (2160p, 20 fps). Multi-view videos were calibrated, segmented, and reconstructed with 4D Gaussian Splatting. Reconstructed point clouds were converted to fixed-connectivity edge graphs for region-of-interest (ROI) displacement tracking and a relative surface-based stress proxy. Stress-proxy values were derived from edge stretch using a Neo-Hookean mapping and reported as comparative surface metrics. A synthetic Blender pipeline with known deformation provided geometric and temporal validation. Results: In synthetic bulk translation, the stress proxy remained near zero for most edges (median approx 0 MPa; 90th percentile 0.028 MPa), with sparse outliers. In synthetic pulling (1-5 mm), reconstruction showed close geometric and temporal agreement with ground truth, with symmetric Chamfer distance of 1.714-1.815 mm and precision of 0.964-0.972 at τ= 1 mm. In preliminary benchtop comparative trials (one trial per condition), cervical aspiration catheter placement showed higher max-median ROI displacement and stress-proxy values than internal carotid artery terminus placement. Conclusion: The proposed protocol provides standardized, time-resolved surface kinematics and comparative relative displacement and stress proxy measurements for thrombectomy benchtop studies. The framework supports condition-to-condition comparisons and methods validation, while remaining distinct from absolute wall-stress estimation. Implementation code and example data are available at https://ethanuser.github.io/vessel4D

Finite element stress fields often exhibit strong local non-smoothness, where stress concentrations near holes, notches, and loading regions induce sharp spatial gradients and high-frequency graph components. Although graph neural networks naturally operate on irregular finite element meshes, conventional message passing is inherently smoothing and progressively attenuates such high-frequency information. Unitary propagation alleviates this problem by preserving spectral magnitudes, but typically relies on matrix functions and high-order approximations with O(Ked) propagation complexity. We propose LiftGCN, an efficient spectrally stable graph network based on Joukowski spectral lifting. LiftGCN maps the real spectrum of a normalized graph operator onto the unit circle through the Joukowski relation and realizes the resulting spectral transformation as a simple second-order recurrence, avoiding matrix exponentials, eigendecomposition, and high-order polynomial truncation. We show that the linear Joukowski backbone has unit-modulus characteristic roots and admits an energy-preserving structure under a positive-definite metric, preventing exponential attenuation of graph-frequency components with depth. Each layer requires only one sparse neighborhood aggregation, yielding O(ed) propagation complexity, while lightweight local nonlinear residuals provide expressive feature transformations. Experiments on finite element stress prediction demonstrate that LiftGCN achieves competitive overall accuracy while improving reconstruction of stress concentrations and local high-gradient structures with substantially reduced computational cost. Our code is available at https://github.com/ChenZeng001/LiftGCN.

Viscosity measurement is essential for process monitoring and autonomous laboratory operation, yet conventional viscometers remain invasive and require controlled laboratory environments that differ substantially from real process conditions. We present a computer-vision-based viscometer that infers viscosity by exploiting how a fixed background pattern becomes optically distorted as light refracts through the mixing-driven, continuously deforming free surface. Under diverse lighting conditions, the system achieves a mean absolute error of 0.113 in log m2 s^-1 units for regression and reaches up to 81% accuracy in viscosity-class prediction. Although performance declines for classes with closely clustered viscosity values, a multi-pattern strategy improves robustness by providing enriched visual cues. To ensure sensor reliability, we incorporate uncertainty quantification, enabling viscosity predictions with confidence estimates. This stand-off viscometer offers a practical, automation-ready alternative to existing viscometry methods.

In this work, we propose a framework that constructs reduced order models for nonlinear structural mechanics in a nonintrusive fashion, and can handle large scale simulations. We identify three steps that are carried out separately in time, and possibly on different devices: (i) the production of high-fidelity solutions by a commercial software, (ii) the offline stage of the model reduction and (iii) the online stage where the reduced order model is exploited. The nonintrusivity assumes that only the displacement field solution is known, and relies on operations on simulation data during the offline phase by using an in-house code. The compatibility with a new commercial code only needs the implementation of a routine converting the mesh and result format into our in-house data format. The nonintrusive capabilities of the framework are demonstrated on numerical experiments using commercial versions of the finite element softwares Zset and Ansys Mechanical. The nonlinear constitutive equations are evaluated by using the same external plugins as for Zset or Ansys Mechanical. The large scale simulations are handled using domain decomposition and parallel computing with distributed memory. The features and performances of the framework are evaluated on two numerical applications involving elastoviscoplastic materials: the second one involves a model of high-pressure blade, where the framework is used to extrapolate cyclic loadings in 6.5 hours, whereas the reference high-fidelity computation would take 9.5 days.

Multiscale problems are ubiquitous in physics. Numerical simulations of such problems by solving partial differential equations (PDEs) at high resolution are computationally too expensive for many-query scenarios, e.g., uncertainty quantification, remeshing applications, topology optimization, and so forth. This limitation has motivated the application of data-driven surrogate models, where the microscale computations are substituted with a surrogate, usually acting as a black-box mapping between macroscale quantities. These models offer significant speedups but struggle with incorporating microscale physical constraints, such as the balance of linear momentum and constitutive models. In this contribution, we propose Equilibrium Neural Operator (EquiNO) as a complementary physics-informed PDE surrogate for predicting microscale physics and compare it with variational physics-informed neural and operator networks. Our framework, applicable to the so-called multiscale FE^{,2}, computations, introduces the FE-OL approach by integrating the finite element (FE) method with operator learning (OL). We apply the proposed FE-OL approach to quasi-static problems of solid mechanics. The results demonstrate that FE-OL can yield accurate solutions even when confronted with a restricted dataset during model development. Our results show that EquiNO achieves speedup factors exceeding 8000-fold compared to traditional methods and offers an optimal balance between data-driven and physics-based strategies.

This paper introduces an advanced Computational Analytical Micromechanics (CAM) framework for linear thermoelastic composites (CMs) with periodic microstructures. The approach is based on an exact new Additive General Integral Equation (AGIE), formulated for compactly supported loading conditions, such as body forces and localized thermal effects (for example laser heating). In addition, new general integral equations (GIEs) are established for arbitrary mechanical and thermal loading. A unified iterative scheme is developed for solving the static AGIEs, where the compact support of loading serves as a new fundamental training parameter. At the core of the methodology lies a generalized Representative Volume Element (RVE) concept that extends Hill classical definition of the RVE. Unlike conventional RVEs, this generalized RVE is not fixed geometrically but emerges naturally from the characteristic scale of localized loading, thereby reducing the analysis of an infinite periodic medium to a finite, data-driven domain. This formulation automatically filters out nonrepresentative subsets of effective parameters while eliminating boundary effects, edge artifacts, and finite-size sample dependencies. Furthermore, the AGIE-based CAM framework integrates seamlessly with machine learning (ML) and neural network (NN) architectures, supporting the development of accurate, physics-informed surrogate nonlocal operators.

It is demonstrated that self-diffusion and shear viscosity data for the TIP4P/Ice water model reported recently [L. Baran, W. Rzysko and L. MacDowell, J. Chem. Phys. {\bf 158}, 064503 (2023)] obey the microscopic version of the Stokes-Einstein relation without the hydrodynamic diameter.

The elastic response of mechanical, chemical, and biological systems is often modeled using a discrete arrangement of Hookean springs, either representing finite material elements or even the molecular bonds of a system. However, to date, there is no direct derivation of the relation between a general discrete spring network, with arbitrary geometry, and it's corresponding elastic continuum. Furthermore, understanding the network's mechanical response requires simulations that may be expensive computationally. Here we report a method to derive the exact elastic continuum model of any discrete network of springs, requiring network geometry and topology only. We identify and calculate the so-called "non-affine" displacements. Explicit comparison of our calculations to simulations of different crystalline and disordered configurations, shows we successfully capture the mechanics even of auxetic materials. Our method is valid for residually stressed systems with non-trivial geometries, and is an essential step in generalizing active stresses on such discrete systems. It is easily generalizable to other discrete models, and opens the possibility of a rational design of elastic systems.

This paper proposes a formal framework for reverse stress testing geopolitical risk in corporate credit portfolios. A joint macro-financial scenario vector, augmented with an explicit geopolitical risk factor, is mapped into stressed probabilities of default and losses given default. These stresses are then propagated to portfolio tail losses through a latent factor structure and translated into a stressed CET1 ratio, jointly accounting for capital depletion and risk-weighted asset dynamics. Reverse stress testing is formulated as a constrained maximum likelihood problem over the scenario space. This yields a geopolitical point reverse stress test, or design point, defined as the most probable scenario that breaches a prescribed capital adequacy constraint under a reference distribution. The framework further characterises neighbourhoods and near optimal sets of reverse stress scenarios, allowing for sensitivity analysis and governance oriented interpretation. The approach is compatible with internal rating based models and supports implementation at the exposure or sector level.

The aim of the present work is to investigate the influence of the realistic model parameters on the equipartition of energy in a vibrofluidized system. To achieve this, a three-dimensional vertically vibrated granular system consisting of spherical particles is simulated using the discrete element method (DEM) using the open-source software LAMMPS. Interparticle and wall-particle interactions are determined using the linear-spring dashpot model. Simulations are performed for nearly perfectly smooth to nearly perfectly rough particles. Two different values for the ratio of the tangential to normal spring stiffness coefficient kappa (2/7 and 3/4) are chosen. Non-equipartition of energy between the translational and rotational modes is observed for all realistic values in the parametric range.

Recent work in scientific machine learning (SciML) has focused on incorporating partial differential equation (PDE) information into the learning process. Much of this work has focused on relatively ``easy'' PDE operators (e.g., elliptic and parabolic), with less emphasis on relatively ``hard'' PDE operators (e.g., hyperbolic). Within numerical PDEs, the latter problem class requires control of a type of volume element or conservation constraint, which is known to be challenging. Delivering on the promise of SciML requires seamlessly incorporating both types of problems into the learning process. To address this issue, we propose ProbConserv, a framework for incorporating conservation constraints into a generic SciML architecture. To do so, ProbConserv combines the integral form of a conservation law with a Bayesian update. We provide a detailed analysis of ProbConserv on learning with the Generalized Porous Medium Equation (GPME), a widely-applicable parameterized family of PDEs that illustrates the qualitative properties of both easier and harder PDEs. ProbConserv is effective for easy GPME variants, performing well with state-of-the-art competitors; and for harder GPME variants it outperforms other approaches that do not guarantee volume conservation. ProbConserv seamlessly enforces physical conservation constraints, maintains probabilistic uncertainty quantification (UQ), and deals well with shocks and heteroscedasticities. In each case, it achieves superior predictive performance on downstream tasks.

Materials that undergo internal transformations are usually described in solid mechanics by multi-well energy functions that account for both elastic and transformational behavior. In order to separate the two effects, physicists use instead phase-field-type theories where conventional linear elastic strain is quadratically coupled to an additional field that describes the evolution of the reference state and solely accounts for nonlinearity. In this paper we propose a systematic method allowing one to split the non-convex energy into harmonic and nonharmonic parts and to convert a nonconvex mechanical problem into a partially linearized phase-field problem. The main ideas are illustrated using the simplest framework of the Peierls-Nabarro dislocation model.

We investigate a coupled system of partial differential equations modeling the interaction between Brinkman flow, biofilm evolution, and nutrient transport in a porous medium. The model captures the mutual influence between the fluid velocity and the biofilm through drag and diffusion coefficients that depend on the local biofilm volume fraction. A hard constraint on the admissible range of the biofilm fraction is incorporated through the subdifferential of an indicator functional, which leads naturally to an evolution variational inequality formulation for the biofilm dynamics. Assuming standard coercivity, ellipticity, and growth conditions on the model coefficients and reaction terms, we prove the global-in-time existence of weak solutions. The analysis relies on a decomposition of the system into three interconnected subproblems: the Brinkman equation with a fixed biofilm profile, the constrained biofilm evolution treated through maximal monotone operator theory, and the nutrient equation viewed as a semilinear parabolic problem. These components are then coupled through a Leray--Schauder type fixed-point argument, with the passage to the limit justified by Aubin--Lions and Simon compactness results. We further establish the nonnegativity of the nutrient concentration under a natural quasi-positivity assumption on the reaction term. Finally, we provide conditional uniqueness results for weak solutions in two spatial dimensions under additional smallness assumptions.

Surface bubbles are an abundant source of aerosols, with important implications for climate processes. In this context, we investigate the stability and thinning dynamics of soap films under effective gravity fields. Experiments are performed using a centrifugal thin-film balance capable of generating accelerations from 0.2 up to 100 times standard gravity, combined with thin-film interferometry to obtain time-resolved thickness maps. Across all experimental conditions, the drainage dynamics are shown to be governed by capillary suction and marginal regeneration-a mechanism in which thick regions of the film are continuously replaced by thin film elements (TFEs) formed at the meniscus. We consistently recover a thickness ratio of 0.8 - 0.9 between the TFEs and the adjacent film, in agreement with previous observations under standard gravity. The measured thinning rates also follow the predicted scaling laws. We identified that gravity has three distinct effects: (i) it induces a strong stretching of the initial film, extending well beyond the linear-elastic regime; (ii) it controls the meniscus size, and thereby the amplitude of the capillary suction and the drainage rate; and (iii) it reveals an inertia-to-viscous transition in the motion of TFEs within the film. These results are supported by theoretical modeling and highlight the robustness of marginal regeneration and capillary-driven drainage under extreme gravity conditions.

This work presents an enhanced Computational Analytical Micromechanics (CAM) framework for the analysis of linear thermoelastic composite materials (CMs) with random microstructure. The proposed approach is grounded in an exact Additive General Integral Equation (AGIE), specifically formulated for compactly supported loading, including both body forces and localized thermal changes (such as those from laser heating). New general integral equations (GIEs) for arbitrary mechanical and thermal loading are proposed. A unified iterative solution strategy is developed for the static AGIE, applicable to CMs with both perfectly and imperfectly bonded interfaces, where the compact support of loading is introduced as a new fundamental training parameter. Central to this methodology is a generalized Representative Volume Element (RVE) concept, which extends Hill classical definition. The resulting RVE is not predefined geometrically, but rather emerges from the characteristic scale of the localized loading, effectively reducing the analysis of an infinite, randomly heterogeneous medium to a finite, data-driven domain. This generalized RVE approach enables automatic exclusion of unrepresentative subsets of effective parameters, while inherently eliminating boundary effects, edge artifacts, and finite size limitations. Moreover, the AGIE-based CAM framework is naturally compatible with machine learning (ML) and neural network (NN) architectures, facilitating the construction of accurate and physically informed surrogate nonlocal operators.

Biological tissues exhibit complex behaviors with their dynamics often resembling inert soft matter such as liquids, polymers, colloids, and liquid crystals. These analogies enable physics-based approaches for investigations of emergent behaviors in biological processes. A well-studied case is the spreading of cellular aggregates on solid surfaces, where they display dynamics similar to viscous droplets. In vivo, however, cells and tissues are in a confined environment with varying geometries and mechanical properties to which they need to adapt. In this work, we compressed cellular aggregates between two solid surfaces and studied their dynamics using microscopy, and computer simulations. The confined cellular aggregates transitioned from compressed spheres into dynamic living capillary bridges exhibiting bridge thinning and a convex-to-concave meniscus curvature transition. We found that the stability of the bridge is determined by the interplay between cell growth and cell spreading on the confining surfaces. This interaction leads to bridge rupture at a critical length scale determined by the distance between the plates. The force distributions, formation and stability regimes of the living capillary bridges were characterized with full 3D computer simulations that included cell division, migration and growth dynamics, directly showing how mechanical principles govern the behavior of the living bridges; cellular aggregates display jamming and stiffening analogously to granular matter, and cell division along the long axis enhances thinning. Based on our results, we propose a new class of active soft matter behavior, where cellular aggregates exhibit liquid-like adaptation to confinement, but with self-organized rupturing driven by biological activity.

This paper establishes Lipschitz stability for the simultaneous recovery of a variable density coefficient and the initial displacement in a damped biharmonic wave equation. The data consist of the boundary Cauchy data for the Laplacian of the solution, \(Δu |_{\partial Ω}\) and \( \partial_{n}(Δu)|_{\partial Ω}.\) We first prove that the associated system operator generates a contraction semigroup, which ensures the well-posedness of the forward problem. A key observability inequality is then derived via multiplier techniques. Building on this foundation, explicit stability estimates for the inverse problem are obtained. These estimates demonstrate that the biharmonic structure inherently enhances the stability of parameter identification, with the stability constants exhibiting an explicit dependence on the damping coefficient via the factor \( (1 + γ)^{1/2} \). This work provides a rigorous theoretical basis for applications in non-destructive testing and dynamic inversion.

Implicit Neural Spatial Representation (INSR) has emerged as an effective representation of spatially-dependent vector fields. This work explores solving time-dependent PDEs with INSR. Classical PDE solvers introduce both temporal and spatial discretizations. Common spatial discretizations include meshes and meshless point clouds, where each degree-of-freedom corresponds to a location in space. While these explicit spatial correspondences are intuitive to model and understand, these representations are not necessarily optimal for accuracy, memory usage, or adaptivity. Keeping the classical temporal discretization unchanged (e.g., explicit/implicit Euler), we explore INSR as an alternative spatial discretization, where spatial information is implicitly stored in the neural network weights. The network weights then evolve over time via time integration. Our approach does not require any training data generated by existing solvers because our approach is the solver itself. We validate our approach on various PDEs with examples involving large elastic deformations, turbulent fluids, and multi-scale phenomena. While slower to compute than traditional representations, our approach exhibits higher accuracy and lower memory consumption. Whereas classical solvers can dynamically adapt their spatial representation only by resorting to complex remeshing algorithms, our INSR approach is intrinsically adaptive. By tapping into the rich literature of classic time integrators, e.g., operator-splitting schemes, our method enables challenging simulations in contact mechanics and turbulent flows where previous neural-physics approaches struggle. Videos and codes are available on the project page: http://www.cs.columbia.edu/cg/INSR-PDE/

Simulating physical systems governed by Lagrangian dynamics often entails solving partial differential equations (PDEs) over high-resolution spatial domains, leading to significant computational expense. Reduced-order modeling (ROM) mitigates this cost by evolving low-dimensional latent representations of the underlying system. While neural ROMs enable querying solutions from latent states at arbitrary spatial points, their latent states typically represent the global domain and struggle to capture localized, highly dynamic behaviors such as fluids. We propose a sampling-based reduction framework that evolves Lagrangian systems directly in physical space over the particles themselves, reducing the number of active degrees of freedom via data-driven neural PDE operators. To enable querying at arbitrary spatial locations, we introduce a learnable kernel parameterization that uses local spatial information from time-evolved sample particles to infer the underlying solution manifold. Empirically, our approach achieves a 6.6x to 32x reduction in input dimensionality while maintaining high-fidelity evaluations across diverse Lagrangian regimes, including fluid flows, granular media, and elastoplastic dynamics. We refer to this framework as GIOROM (Geometry-Informed Reduced-Order Modeling). All code and data are available at: https://github.com/HrishikeshVish/GIOROM

During electrostatic bonding, also known as anodic bonding, silicon is bonded to glass by applying an external voltage and simultaneous heating to temperatures of 200...450 °C. While cooling to working temperature after bonding happened pieces are mutually deformed. Due to linear thermal expansion coefficients mismatch of anodically bonded glass and silicon samples an internal stress state is generated. Such stresses are called thermal mismatch stresses. The aim of this paper is a determination of technological and design solutions to achieve minimal thermal mismatch stresses in resulting bond. The nonlinear dependence of linear thermal expansion coefficients of bonded samples' materials on temperature makes it difficult to minimize thermal mismatch stresses by chosing materials with close average thermal expansion coefficients in particular temperature range. To assess means of lowering thermal mismatch stress in this paper two different ways to describe assembly are used: two thin bonded layers and multilayered composite material. Based on properties of two brands of glass (LK5, Borofloat 33) and silicon used with described mathematical models thermal mismatch stresses at temperature T_w in samples bonded at several different temperatures T_b are evaluated. Bonded silicon surface stress dependence of glass to silicon wafer thickness ratio is evaluated. Based on such evaluations one can say that by varying thickness of glass bonded to silicon one can obtain zero thermal mismatch stress at a particular depth of material or obtain stress of some defined value at this depth. Models of assembly description used in this paper can be used to optimize anodic bonding process parameters. Such usage aimed to minimize thermal mismatch stresses at device working temperatures is presented in this paper.

The NMR measurements performed on a single orthorhombic crystal of superconducting ferromagnet UCoGe (Y.Ihara et al, Phys. Rev. Lett. v.105, 206403 (2010)) demonstrate strongly anisotropic magnetic properties of this material. The presented calculations allow to establish the dependence of longitudinal spin-lattice relaxation rate from temperature and magnetic field. The value 1/T_1T in field perpendicular to spontaneous magnetisation directed along c-axis has maximum in vicinity of Curie temperature whereas it does not reveal similar behaviour in field parallel to the direction of spontaneous magnetisation. Also there was shown that the longitudinal spin-lattice relaxation rate is strongly field dependent when the field directed in b-crystallographic direction but field independent if magnetic field is oriented along a-axis.

Physics-Informed machine learning models have recently emerged with some interesting and unique features that can be applied to reservoir engineering. In particular, physics-informed neural networks (PINN) leverage the fact that neural networks are a type of universal function approximators that can embed the knowledge of any physical laws that govern a given data-set in the learning process, and can be described by partial differential equations. The transient diffusivity equation is a fundamental equation in reservoir engineering and the general solution to this equation forms the basis for Pressure Transient Analysis (PTA). The diffusivity equation is derived by combining three physical principles, the continuity equation, Darcy's equation, and the equation of state for a slightly compressible liquid. Obtaining general solutions to this equation is imperative to understand flow regimes in porous media. Analytical solutions of the transient diffusivity equation are usually hard to obtain due to the stiff nature of the equation caused by the steep gradients of the pressure near the well. In this work we apply physics-informed neural networks to the one and two dimensional diffusivity equation and demonstrate that decomposing the space domain into very few subdomains can overcome the stiffness problem of the equation. Additionally, we demonstrate that the inverse capabilities of PINNs can estimate missing physics such as permeability and distance from sealing boundary similar to buildup tests without shutting in the well.

Offline goal-conditioned reinforcement learning (GCRL) learns goal-conditioned policies from static pre-collected datasets. However, accurate value estimation remains a challenge due to the limited coverage of the state-action space. Recent physics-informed approaches have sought to address this by imposing physical and geometric constraints on the value function through regularization defined over first-order partial differential equations (PDEs), such as the Eikonal equation. However, these formulations can often be ill-posed in complex, high-dimensional environments. In this work, we propose a physics-informed regularization derived from the viscosity solution of the Hamilton-Jacobi-Bellman (HJB) equation. By providing a physics-based inductive bias, our approach grounds the learning process in optimal control theory, explicitly regularizing and bounding updates during value iterations. Furthermore, we leverage the Feynman-Kac theorem to recast the PDE solution as an expectation, enabling a tractable Monte Carlo estimation of the objective that avoids numerical instability in higher-order gradients. Experiments demonstrate that our method improves geometric consistency, making it broadly applicable to navigation and high-dimensional, complex manipulation tasks. Open-source codes are available at https://github.com/HrishikeshVish/phys-fk-value-GCRL.

We propose a hybrid neural network (NN) and PDE approach for learning generalizable PDE dynamics from motion observations. Many NN approaches learn an end-to-end model that implicitly models both the governing PDE and constitutive models (or material models). Without explicit PDE knowledge, these approaches cannot guarantee physical correctness and have limited generalizability. We argue that the governing PDEs are often well-known and should be explicitly enforced rather than learned. Instead, constitutive models are particularly suitable for learning due to their data-fitting nature. To this end, we introduce a new framework termed "Neural Constitutive Laws" (NCLaw), which utilizes a network architecture that strictly guarantees standard constitutive priors, including rotation equivariance and undeformed state equilibrium. We embed this network inside a differentiable simulation and train the model by minimizing a loss function based on the difference between the simulation and the motion observation. We validate NCLaw on various large-deformation dynamical systems, ranging from solids to fluids. After training on a single motion trajectory, our method generalizes to new geometries, initial/boundary conditions, temporal ranges, and even multi-physics systems. On these extremely out-of-distribution generalization tasks, NCLaw is orders-of-magnitude more accurate than previous NN approaches. Real-world experiments demonstrate our method's ability to learn constitutive laws from videos.

Sycophancy in LLMs is documented across 70+ papers, but expert agreement on construct boundaries remains low (ICC=.184; Ye et al., 2026). The construct fragments because behavioral classification depends on which surface form is privileged. We adopt a materials-science framing: conversation as test specimen under load, LLM-model as material charge, pushback as progressive load, stance-flip as material failure. We characterize this failure across three loading cases (debate n=1000; false-presuppositions n=3400; ethical-setting n=3400; 10-17 material charges per case; 7800 specimens total) using 14 turn-level axis-measurements spanning velocity, damage accumulation, frame-drift, brittleness, and direction stability, plus three speaker-resolved axes from an independent pipeline. The measurements are Hooke-coupled (σ= E cdot varepsilon analog) and reproduce across loading cases with effects up to |r_{rb}| = 0.35 on debate; the sign structure adds a second pattern: the ethical-setting case inverts the velocity and accumulation blocks. Variance composition partitions into two profiles: debate is charge-dominated (brittle-fracture-like: the material grade decides), false-presuppositions and ethical-setting are topic-dominated (creep-like: the load decides); the ratios (2.03 vs 0.13/0.17) are estimator-dependent, for debate even in direction. Cross-judge reliability (GPT-4o vs Haiku 4.5) shows debate scoring is judge-robust (Cohen's κ= 0.88) while false-presupposition scoring is judge-sensitive (κ= 0.36) -- a caveat single-judge benchmarks must report. This is the methodological move Ye et al.'s diagnosis calls for: a multi-axis characterization that does not depend on which surface form of the construct one privileges.

We consider the scattering of acoustic perturbations in a presence of a flow. We suppose that the space can be split into a zone where the flow is uniform and a zone where the flow is potential. In the first zone, we apply a Prandtl-Glauert transformation to recover the Helmholtz equation. The well-known setting of boundary element method for the Helmholtz equation is available. In the second zone, the flow quantities are space dependent, we have to consider a local resolution, namely the finite element method. Herein, we carry out the coupling of these two methods and present various applications and validation test cases. The source term is given through the decomposition of an incident acoustic field on a section of the computational domain's boundary.

In agentic scientific machine learning (SciML), large language model (LLM) agents can discover surrogate models and select one by an automated score, typically an error metric. A low error, however, does not establish that the predicted fields satisfy the physics that matter for mechanics, such as boundary conditions, superposition, stiffness scaling, or causality. We introduce Physics-Audited Agentic SciML (PA-SciML), a verification-first workflow for agentic SciML discovery. The workflow fixes a scoring evaluator before search, derives reviewable machine-checkable physics requirements, checks each trained candidate on its outputs, and separately searches prescribed input ranges or measured load-history spans for high-violation cases without reference solution fields. A surrogate is reported as verified only under the stated checks. When enabled, the workflow also adds advisory numerical probes before training and tests one modeling change at a time to record which isolated edits are associated with score gains before reuse. In the reported computational-solid-mechanics numerical examples, the static elasticity run selects a surrogate with lower validation error than the error-only baseline while both selected models pass the common linear-elastic checks. In the transient elastodynamics run, an error-only baseline with similar mean error fails a stricter causality check by responding to future parts of the loading history, while the selected surrogate passes the stated checks. The main distinction is per-candidate physics evidence on predicted fields, not a richer aggregate score.

Engineered timber is pivotal to low-carbon construction, but moisture uptake during its service life can compromise structural reliability and impede reuse within a circular economy model. Despite growing interest, quantitative standards for classifying the reusability of moisture-exposed timber are still lacking. This study develops a probabilistic framework to determine the post-exposure reusability of engineered timber. Laminated specimens were soaked to full saturation, dried to 25% moisture content, and subjected to destructive three-point flexural testing. Structural integrity was quantified by a residual-performance metric that assigns 80% weight to the retained flexural modulus and 20% to the retained maximum load, benchmarked against unexposed controls. A hierarchical Bayesian multinomial logistic model with horseshoe priors, calibrated through Markov-Chain Monte-Carlo sampling, jointly infers the decision threshold separating three Modern Methods of Construction (MMC) reuse levels and predicts those levels from five field-measurable features: density, moisture content, specimen size, grain orientation, and surface hardness. Results indicate that a single wet-dry cycle preserves 70% of specimens above the 0.90 residual-performance threshold (Level 1), whereas repeated cycling lowers the mean residual to 0.78 and reallocates many specimens to Levels 2-3. The proposed framework yields quantified decision boundaries and a streamlined on-site testing protocol, providing a foundation for robust quality assurance standards.

The friction coefficient of a particle can depend on its position as it does when the particle is near a wall. We formulate the dynamics of particles with such state-dependent friction coefficients in terms of a general Langevin equation with multiplicative noise, whose evaluation requires the introduction of specific rules. Two common conventions, the Ito and the Stratonovich, provide alternative rules for evaluation of the noise, but other conventions are possible. We show the requirement that a particle's distribution function approach the Boltzmann distribution at long times dictates that a drift term must be added to the Langevin equation. This drift term is proportional to the derivative of the diffusion coefficient times a factor that depends on the convention used to define the multiplicative noise. We explore the consequences of this result in a number examples with spatially varying diffusion coefficients. We also derive path integral representations for arbitrary interpretation of the noise, and use it in a perturbative study of correlations in a simple system.

We study uncertainty quantification for partial differential equations subject to domain uncertainty. We parameterize the random domain using the model recently considered by Chernov and Le (2024) as well as Harbrecht, Schmidlin, and Schwab (2024) in which the input random field is assumed to belong to a Gevrey smoothness class. This approach has the advantage of being substantially more general than models which assume a particular parametric representation of the input random field such as a Karhunen-Loeve series expansion. We consider both the Poisson equation as well as the heat equation and design randomly shifted lattice quasi-Monte Carlo (QMC) cubature rules for the computation of the expected solution under domain uncertainty. We show that these QMC rules exhibit dimension-independent, essentially linear cubature convergence rates in this framework. In addition, we complete the error analysis by taking into account the approximation errors incurred by dimension truncation of the random input field and finite element discretization. Numerical experiments are presented to confirm the theoretical rates.